I confirm this. Live Events Think Alpha Series. Dandy vs Scan. TerrOr vs Scan. Live Streams StarCraft 2 Forgg! Mang0 ChuDatz Organizations Other Games gamesdonequick BasetradeTV Blizzard YouTube. Online Event. Moscow Cybersport Series. GeNieS vs Bee. ESL Pro Tour. Shinhan Tank Proleague. Matvey vs Fallenger. BW Jeez Weekly. Hawk vs KenZy. TT1 vs spx. Alpha Pro Series. MilkiCow vs Matvey.
MilkiCow vs Fallenger. Dandy vs Dienmax. Grand Platypus Open. Liquipedia Results Completed. PiG Sty Festival. X-Cup Fall - Qual. Pinnacle Fall Series 2. RCG Samsung LPG 1. Shinhan Tank Proleague S5. At least for the average consumer market. The second revision socket motherboards support only DDR4 memory. VGA output is optional since Intel dropped support for this video interface starting with Skylake. No, absolutely not. They are not compatible. The numbers refer to the amount of pins found in the socket and on the CPU.
In the case of say vs , even if you could get the CPU to fit, the functions of the pins have been switched around with LGA because according to Intel, it improved efficiency. Socket LGA uses a land grid array format, so the pins are on the socket, rather than the processor. Socket LGA uses the same cover plate as Socket , but is not interchangeable with it. LGA has protruding pins to make contact with the pads on the processor. Processors for LGA and LGA sockets are not compatible with each other since they have different socket notches.
They both provide great performance and have been loaded with power conservation features. Do not touch the Orientation Notches. The socket has cutouts for your fingers to fit into. Verify that the processor is in the socket body and properly oriented in the socket. Make sure the front edge of the load plate slides under the shoulder screw cap as the lever is lowered.
Latch the lever under the corner tab of the top plate, being cautious not to damage the motherboard with the tip of the lever. To prevent damage, avoid setting the fan heat sink with the prongs down. Set it on its side or with the fan-side down. Make sure fasteners are flush with motherboard.
Make sure fastener slots are pointing perpendicular to heat sink. While holding heat sink, press down on fastener caps with thumb to install and lock. Repeat until all four fasteners are locked in place. Make sure both fastener cap and base are flush with spring and motherboard. Connect fan cable to motherboard CPU header. Secure excess cable with tie-wrap to ensure cable does not interfere with fan operation or contact other components.
Turn fastener caps 1 counter-clockwise 90 degrees to the unlocked position. You might need to use a flathead screwdriver to unlock the fasteners. Manually remove heat sink with gentle twisting motion. Keeping the processor horizontal, remove the processor with a vertical motion to avoid damaging the socket contacts. Protect the processor by putting it in a specially designed tray or ESD retainer for storage.
Do not allow the processor to reset on the gold lands. Carefully lower protective cover on hinge side first, to contact with the outside wall of the LGAx socket:. Engage protective cover retention features to outside of LGAx socket, and align two cover corners to socket corners. This step is critical to avoid Bent Contact Damage. Hold cover and move gently from side-to-side.
Feel the play with the cover and socket to verify that the protective cover is properly seated. Close the socket load plate and engage the load lever. Contact support. Characters remaining: We appreciate all feedback, but cannot reply or give product support. Please do not enter contact information. If you require a response, contact support. Safari Chrome Edge Firefox. Support Navigation Support. Support Home Processors.
Close Window. Click or the topic for details: Handling procedures Motherboard handling Remove motherboard from ESD bag if applicable. Make sure socket load lever and load plate are secured. Do not open socket at this time. Socket preparation To open the socket, follow these steps.
Rotate load lever to open position at about degrees. Note Apply pressure when pressing the load lever, or the lever bounces back, like a mouse trap, and can cause bent contacts. To remove the socket protective cover, follow these steps. Lift protective cover away from the socket, being careful not to touch the electrical contacts.
Caution Vertical removal is not recommended, as it requires higher force and can lead to socket contact damage.
0コメント